This article may contain some affiliate links and if you make a purchase after clicking on any of teh links, we may earn a small commission at no additional cost to you.
How far can a washing machine pump its waste? This is a concern for many washing machine owners who are confused about the capacity of the washing machine they are buying.
For the drain hose on your Top Load washer to work appropriately, the drain must be 30″ up from the floor at minimal and shorter than 8 feet. For the drain hose on your Front Load washer to perform suitably, the drain should be at least 24″ up from the floor and less than 8 feet high.
GE and Hotpoint Top Load, Front Load and Unitized washers possess drain pumps that can pump water upright as high as 8 feet. Spacemaker washers can pump up to 5 feet.
What Determines the Pump Rate of Washing Machine Pumps?
The discharge velocity of the pump relies on the height of the drain pipe. The Top Load washer pump for example will pump water at a proportion of 15 gallons per minute. The Front Load washer pump will pump water at an amount of 10 gallons per minute.
For each 1 foot of extra drain pipe length, the flow rate will be decreased by roughly 1 gallon per minute. The drain pipe should be at least 1-1/2″ I.D., to guarantee proper draining. The washer drain hose is a 1-1/4″ O.D.
To be convinced that no siphoning of water will occur, the drain plumbing must be at least 30″ long for Top Load washers. Siphoning in this context implies the washer will fill and deplete at the same time. This occurs when the drain length is too poor.
Siphoning can also happen if the drain hose is hoisted too distantly down into the drain pipe. For recent Top Load washers, the drain hose shouldn’t be more than 5″ down into the drain pipe. For Front Load washers, the drain hose shouldn’t be more than 7″ down into the drain pipe.
See Also: How High Can a Washing Machine Pump?
NOTE! If the vent for your Top Load washer is not 30″ high, contained in the installation container with a new Top Load washer is a drain hose clip, it is at times known as an anti-siphon clip that binds to the hose and the back of the washer to hoist the drain hose up higher.
This is not required for a Front Load washer though, because of the structure of the unit.
You will see that most washing machines state the maximum and minimum lengths of the outlet. One thing to worry about on high outlets, however, is that water will fall back into the washing machine, resulting in damp harm, fungi, and other unpleasantness.
That is why there MUST be a hitch in the pipe and it normally explains that it isn’t taller than the washing machine itself. I am certain it will work but it will decrease the life of your machine and probably develop health problems for you too!
What you possess now is somewhat accurate. Another thing to be examined is all that quantity of water in the hose that never gets pumped out, simply to drain back into the tub when the pump cycle quits. Greywater fanatics have a lot of knowledge about running wash machine water bigger than vendor directions.
If you check the rules that arrived with the washer, it should include the main drain height. Commonly, the maximum height is approximately 39″ (99 cm).
Modern washers often include a drain hose always attached, which is developed to make the drain structure foolproof. The supply drain hose demonstrates precisely how great the washer can release.
How to Increase Washing Machine Pump Height
1. Raise the Washer
Hinging on the machine, and whether or not you’re already utilizing a pedestal, you may be proficient to lift the whole machine, to achieve what you want.
The ultimate altitude is not height above sea point, it’s the height above the underside of the washer. So if it’s probable to do so, lifting the machine some inches high might be the remedy.
If it’s a front-loading washer; and you’re not already utilizing a pedestal, you may have to obtain or construct a pedestal to lift the machine.
Otherwise, you may want to contemplate building an elevated floor to bring the whole area up.
2. Get Standpipes But Keep it up to Code
International Residential Code (IRC) says:
“Standpipes shall extend a minimum of 18 inches (457 mm) and a maximum of 42 inches (1067 mm) above the trap weir. Access shall be provided to all standpipe traps and drains for rodding.”
This implies that if you attach the drain hose to a standpipe, the standpipe has to be at least 18″ over the point at which water will start to trickle from the trap.
So your 43″ height could promptly become 61″.
I strongly disagree with the usage of hose additions; in situations of necessity, the extension must possess the exact diameter as the initial hose and must not surpass 150 cm in length.
Confirm that if the drain hose is shoved into a standpipe, the edge does not go down more than 15cms (6 inches). If the hose is thrust down too far, this may result in the machine to self -siphon ie. continually vacant.
The 40mm standpipe structure is the conventional setup but an additional drain hose can be utilized although it would require occasional inspections for water leaks as they can leak.
So you can do it but examine your WM instructions.
See Also: Does Washing Machine Heat Water?
Frequently Asked Questions
Can a washing machine drain hose be too long?
Yes, but confirm that the drain hose is not extended, clamped, squashed, or kinked.
Do washing machines drain all the way?
Not really. Many people believe that drainage is something a washing machine does automatically.
How far can a washing machine be from water?
The answer to this question is complicated by the fact that it is much harder to pump water vertically than horizontally.
Do washing machines pump water out?
Yes, they do. The Top Load washer pump pumps water at a proportion of 15 gallons per minute. The Front Load washer pump pumps its water at a proportion of 10 gallons per minute.
How does a washing machine drain pump work?
The washer pump hoists water from the bottom of the machine into the drain hose. The drain hose angles to the height of the appliance, and then under the drain, enabling the tub to fill. When the water gets to the corner in the hose, it takes off out of the drain.
Conclusion: How Far Can a Washing Machine Pump its Waste?
How far can a washing machine pump its waste? The answer to this question varies. It is determined by the length of the drain hose, but it can also be enhanced.
Always check your washing machine manual, and follow the prompts judiciously.